Set Up QR Code Checkpoints

Set a site round checkpoint to QR code, print its code, put the code up, check it with a phone and replace a damaged or missing code.

A site round checkpoint can use a printed QR code. A staff member on a round scans the code with the MyWatchtower phone app to check in at the checkpoint. Your community, or a contractor that your community hires, prints the codes and puts them up. This article tells you how to set up a QR checkpoint, print its code, put the code up, check it and replace it.

Before you start

Your role needs both of these permissions to open the checkpoints, set them up and print their codes:

  • The site round routes write permission (site_round_routes:w).
  • The site rounds read permission (site_rounds:r).

The checkpoints are in Settings > Settings > Site rounds, on the Checkpoints view. If your community gave site rounds another name, the settings section and the tabs show that name.

Set a checkpoint to QR code

1. Open Settings > Settings > Site rounds.

2. On the Checkpoints view, select a checkpoint to edit it, or select Add checkpoint to add one.

3. In Method, select QR code. The staff member then checks in by scanning the printed QR code.

4. Optional: type a Label. The label shows on the printed sheet and when you check a code. Use it to tell two codes apart, for example by a number that you write on the post.

5. Optional: place the checkpoint on the map. A QR checkpoint does not need a zone. The QR code proves the arrival.

6. Select Save. For a new checkpoint, the button is Add.

MyWatchtower makes the QR code when you save. The dialog stays open on the saved checkpoint and shows the code.

If you change a saved QR checkpoint to another method, the printed QR code stops working for new rounds when you save.

Print the codes

You can print the code of one checkpoint, or the codes of many checkpoints at once.

To print the code of one checkpoint:

1. Open the checkpoint.

2. Under QR code, select Print.

To print the codes of a route, or of every QR checkpoint:

1. On the Checkpoints view, select Print QR codes.

2. In Checkpoints to print, select All QR checkpoints, or select one route. The list shows the number of QR codes of each choice.

3. Select Print.

On a computer, MyWatchtower saves a PDF file. In the phone app, the phone's share sheet opens with the PDF file. The sheet has one QR code on each page, with the name of the checkpoint, its label and the line "Scan this code in the MyWatchtower app to check in at this checkpoint." Print the file, and put each code up on its checkpoint.

Print QR codes is not available until at least one checkpoint uses a QR code.

Put the codes up

  • Outdoors, print on weatherproof label stock, or laminate the page. Rain and sun fade plain paper, and a faded code does not scan.
  • Put each code where a phone can reach it: on a flat surface that a staff member can stand close to, with nothing in front of it.
  • Put each code at its own checkpoint. A code that is put up at the wrong place checks the staff member in at the wrong checkpoint.

Check a code

After the codes are up, check each one with a phone. Check a code is in the MyWatchtower phone app only. The web app cannot scan QR codes.

1. In the phone app, open Settings > Settings > Site rounds.

2. On the Checkpoints view, tap Check a code.

3. Point the camera at the posted code.

The app tells you which checkpoint holds the code, for example "This code is on North Gate," and shows its label. If the app says "This code is not on a checkpoint," the code is not the current code of a QR checkpoint of your community. For example, the code was replaced, its checkpoint now uses another method, or it is not a checkpoint code at all, such as a guest's entry QR code. If the code is up at a QR checkpoint, open that checkpoint, print its current code and put it up. If no code is read, try again in better light.

Tap Scan another code to check the next one.

Replace a damaged or missing code

When a code is damaged, faded or missing, make a new code:

1. Open the checkpoint.

2. Under QR code, select Replace code.

3. Read the message, then select Replace code to confirm.

4. Select Print, and put the new code up in place of the old one.

New rounds do not accept the old code. A round that already started keeps the old code. Take down the old code, so that no staff member scans it by mistake.

Replace code is not available when the app is offline.

Check in at a QR checkpoint

On a round, a QR checkpoint shows Scan QR code in the phone app. The staff member taps it and scans the posted code. The app then opens the check-in of that checkpoint.

When the code cannot be scanned, for example because it is missing or the camera is not allowed, the staff member taps Check in without the code and writes a note. The web app offers only Check in without the code at a QR checkpoint.

A check-in with no scan is marked Not verified in Round history and in the round PDF. The note tells you why the code was not scanned. Many check-ins that are not verified at one checkpoint can mean that its code needs to be replaced.

Need help?

On a computer, select Help center in the navigation. On a phone, tap your picture at the top of the screen, then tap Help. Both open the MyWatchtower support page. You can also contact the management office of your community.

Was this article helpful?

Still stuck?

We just need your email address. Or write to support@jekasoftware.com — either way it lands with the same team.

Submit a ticket